How to Tune Up Your Lawn Mower | Ask This Old House


This Old House landscape contractor Roger Cook shares his top five tips for keeping your lawn mower running smoothly. (See below for the shopping list, tools, and steps.)
SUBSCRIBE to This Old House: http://bit.ly/SubscribeThisOldHouse

Shopping List for How to Tune Up Your Lawn Mower:
– Motor oil
– Air filter
– Spark plug
– Gasoline
– Fuel stabilizer

Tools for How to Tune Up Your Lawn Mower:
– Oil container, for collecting old, dirty oil
– Sockets and ratchet wrench, for changing spark plug and removing blade
– Metal file or right-angle grinder, to sharpen blade
– Blade balancer, for balancing blade after sharpening

Steps for How to Tune Up Your Lawn Mower:
1. Check the mower’s oil level before every use. Be sure the mower is on level ground when checking the oil.
2. If the oil is low, add fresh oil to raise the level to the “full” line on the dipstick.
3. If the oil is dirty, change it by tipping the mower onto its side and draining the dirty oil into a container with a tight-fitting lid.
4. Recycle the old, dirty oil at a service station, auto shop, or local transfer station.
5. Add new oil a little at a time, stopping frequently to check the dipstick to avoid over-filling the crankcase.
6. Replace the air filter with a new filter every mowing season, or sooner if the mowing conditions are very dusty.
7. Change the spark plug once a year, or when the engine starts running rough.
8. Remove the old spark plug with a deep socket and ratchet wrench.
9. When installing the new spark plug, hand-thread it into place, then tighten it with the socket and ratchet. However, be careful not to over-tighten the spark plug or it will be difficult to remove next year.
10. Sharpen the blade every mowing season to ensure that it cuts the grass quickly and cleanly.
11. Disconnect the spark plug wire to prevent accidental starting, then tip up the mower to gain access to the blade.
12. Use a ratchet wrench and socket to loosen the nuts that hold the blade in place.
13. Sharpen each end of the blade with a metal file or right-angle grinder. Be sure to maintain the blade’s original bevel angle, and remove the same amount of material from each end.
14. After sharpening, use a balancer to confirm that the blade is perfectly balanced.
15. If the blade is out of balance, file or grind the heavy end of the blade and then recheck it with the balancer.
16. To keep the mower running smoothly, always use fresh gasoline. Stale gas can damage the engine.
17. Buy only enough gas to last one month.
18. To extend the life of gasoline, add a fuel stabilizer.

About Ask This Old House TV:
Homeowners have a virtual truckload of questions for us on smaller projects, and we’re ready to answer. Ask This Old House solves the steady stream of home improvement problems faced by our viewers—and we make house calls! Ask This Old House features some familiar faces from This Old House, including Kevin O’Connor, general contractor Tom Silva, plumbing and heating expert Richard Trethewey, and landscape contractor Roger Cook.

Follow This Old House and Ask This Old House:
Facebook: http://bit.ly/ThisOldHouseFB
Twitter: http://bit.ly/ThisOldHouseTwitter
http://bit.ly/AskTOHTwitter
Pinterest: http://bit.ly/ThisOldHousePinterest
Instagram: http://bit.ly/ThisOldHouseIG
http://bit.ly/AskTOHIG
Tumblr: http://bit.ly/ThisOldHouseTumblr

For more on This Old House and Ask This Old House, visit us at: http://bit.ly/ThisOldHouseWebsite

How to Tune Up Your Lawn Mower | Ask This Old House
https://www.youtube.com/user/thisoldhouse/



Be the first to comment

Leave a Reply

Your email address will not be published.


*